Thermal paste GD100, 1kg, AMPUL.eu
zoom_out_map
chevron_left chevron_right

Thermal paste GD100, 1kg

92.01 €

92.01 € Tax excluded

92.01 €/kg

92.01 € without VAT
check In stock
datasheet

High-quality thermal paste for radiators with a thermal conductivity of up to 1,094W/mK. The thermal paste is designed to ensure better heat transfer between the heat source - the electronic component and its cooler. This fills the unevenness between the surface of the cooler and the surface of the cooled component and thus increases the transfer of heat to the cooler, which then has greater cooling efficiency. Thanks to the use of heat-conducting paste, you will make the cooling more efficient overall and extend the life of the cooled components. Suitable for all semiconductors (LEDs), processors, graphics cards, memory modules and more. The paste is not electrically conductive.

Thermal conductivity: 1.094W/mK

Minimum operating temperature: -50°C

Maximum operating temperature: 200°C

Specific gravity: > 2 g/Cc

Package weight: 1000g

The package also includes a plastic spatula for easier application.

OEM
AM6114
Color
White
Max. operating temperature
200 °C
Thermal conductivity
1.094 W/mK
Amount
1000 g

Introduction

Thermal paste is essential for effective heat dissipation between electronic components, for example between an LED module and a heatsink or between a processor and a heatsink. Proper application ensures that a uniform and thin layer – usually around 0.1 to 0.3 mm – is formed, filling the microscopic irregularities of the surfaces. This step-by-step guide explains how to achieve optimal thermal contact and thereby improve the performance and lifespan of the device.

Materials and Preparation

  • Thermal paste
  • Isopropyl alcohol and a clean cloth or paper towels
  • Protective gloves
  • Antistatic tape (when working with sensitive electronics)

Before you begin, always ensure that the device is completely powered off and disconnected from the power source. This reduces the risk of electric shock.

Procedure for Applying Thermal Paste

  1. Cleaning the Contact Surfaces – Start by carefully cleaning both contact surfaces with isopropyl alcohol and a cloth. This will remove dust, grease, and any remnants of old paste, ensuring a better thermal connection.
  2. Application of the Paste – Apply a small drop of paste, approximately the size of a pea, in the center of the surface. When the heatsink is pressed down, the paste will spread evenly into a thin layer with a thickness of 0.1 to 0.3 mm, which is ideal for effective heat dissipation.
  3. Mounting the Heatsink or LED Module – Place the heatsink or LED module directly onto the designated area and press it firmly to ensure even thermal contact. Proper tightening will prevent the formation of air pockets that could reduce cooling efficiency.
  4. Checking the Distribution of the Paste – If possible, verify that the paste has spread evenly. If necessary, carefully remove any excess paste and reapply a small amount.

Specific Guidelines for LED and Other Devices

  • Apply the paste only to the areas where heat is being dissipated.
  • Avoid contact between the paste and sensitive components, such as the LED diodes themselves.
  • Ensure that the paste does not spread to surrounding parts, where it could affect the device’s functionality.

These steps will help achieve maximum cooling efficiency while ensuring the long-term reliability of your components.

Safety Warnings

  • Disconnect the device from the power source before beginning work.
  • Wear protective gloves and use antistatic tools to minimize the risk of damaging components and injury.
  • Work in a well-ventilated area to avoid inhaling fumes.
  • If the paste comes into contact with your skin or eyes, immediately rinse thoroughly with water.
  • If you have any doubts about the procedure, do not hesitate to seek advice from a professional.

EU Importer: AMPUL SYSTEM s.r.o., Čsl. armády 641/40, 78701 Šumperk, Czech Republic,

6 other products in the same category: